Bronkhorst RS232 interface Bedienungsanleitung PDF herunterladen (Seite 34)

Parameter values table

Parameter

number

(DDE)

Parameter

name

Filter Value Description

2011-05-18 Page 1 of 5 FlowDDE database version V3.64

6 Arbitrage temporary busmaster1

6 Arbitrage always busmaster2

6 Arbitrage automatic busmaster3

6 Arbitrage auto busmaster and auto bus optimalization (fast token ring)67

12 Control mode setpoint = BUS setpoint0

12 Control mode setpoint = analog input1

12 Control mode setpoint = master output(FLOW-BUS) * slave factor(FLOW-BUS)2

12 Control mode close valve3

12 Control mode controller idle (no reaction on changes in sensor signal)4

12 Control mode testmode enable (select subject with par 70)5

12 Control mode tuningmode enable (select subtject with par 79)6

12 Control mode setpoint = 100%7

12 Control mode purge valve (fully open)8

12 Control mode calibration mode enable (select subject with par 58)9

12 Control mode setpoint = master output(analog in) * slave factor(FLOW-BUS)10

12 Control mode setpoint = keyboard OR FLOW-BUS setpoint11

12 Control mode setpoint = 0%12

12 Control mode setpoint = master output(FLOW-BUS) * slave factor(analog in)13

12 Control mode (FPP) Range select mode14

12 Control mode (FPP) Manual start sensor select, automatic end sensor15

12 Control mode (FPP) Automatic start sensor select, manual end sensor16

12 Control mode (FPP) Automatic start and end sensor17

12 Control mode setpoint = RS232 setpoint18

12 Control mode RS232 broadcast mode19

12 Control mode valve stearing (valve = setpoint)20

12 Control mode analog valve stearing (valve = analog setpoint)21

12 Control mode valve safe state22

22 Sensor type pressure (controller)0

22 Sensor type liquid volume (controller)1

22 Sensor type liquid/gas mass (controller)2

22 Sensor type gas volume (controller)3

22 Sensor type other sensor type (controller)4

22 Sensor type pressure (sensor)128

22 Sensor type liquid volume (sensor)129

22 Sensor type liquid/gas mass (sensor)130

22 Sensor type gas volume (sensor)131

22 Sensor type other sensor type (sensor)132

28 Alarm info &H01 no error message in alarm error status register0

28 Alarm info &H01 at least 1 error message in alarm error status register1

28 Alarm info &H02 no warning message in alarm warning status register0

28 Alarm info &H02 at least 1 warning message in alarm warning status register1

28 Alarm info &H04 no minimum alarm message (measure>minimum limit)0

28 Alarm info &H04 minimum alarm message for measured signal1

28 Alarm info &H08 no maximum alarm message (measure<maximum limit)0

28 Alarm info &H08 maximum alarm message for measured signal1

28 Alarm info &H10 batch counter has not reached its limit0

28 Alarm info &H10 batch counter has reached its limit1

28 Alarm info &H20 response O.K. (setpoint-measure within limit)0

28 Alarm info &H20 response alarm message: setpoint-measure is too high1

28 Alarm info &H40 master output signal O.K. (or not used)0

28 Alarm info &H40 master output signal not received: check master instrument1

28 Alarm info &H80 hardware O.K.0

28 Alarm info &H80 hardware error message: check your hardware1

44 Operation mode T/A OFF0

44 Operation mode T/A A: MAX & RESP AUTO; T: UP TO LIMIT1

44 Operation mode T/A A: MIN & RESP AUTO; T: UP AND REPEAT2

44 Operation mode T/A A: MAX & RESP; T: DOWN FROM LIMIT3

44 Operation mode T/A A: MIN & RESP; T: DOWN AND REPEAT4

44 Operation mode T/A A: MAXIMUM ALARM; T: ALWAYS UP5

44 Operation mode T/A A: MINIMUM ALARM6

44 Operation mode T/A A: RESPONSE ALARM7

53 Analog mode &H3F 0...5 Vdc operation0

53 Analog mode &H3F 0...10 Vdc operation1

53 Analog mode &H3F 0...20 mA operation2

53 Analog mode &H3F 4...20 mA operation3

53 Analog mode &H3F 15...20 mA operation4

53 Analog mode &H40 Analog input enabled0

53 Analog mode &H40 Analog input disabled1

53 Analog mode &H80 Analog output enabled0

53 Analog mode &H80 Analog output disabled1

58 Calibration mode idle: no action0

58 Calibration mode adc self calibration1

58 Calibration mode dmfc2

58 Calibration mode dmfc3

58 Calibration mode dmfc4

58 Calibration mode dmfc5

58 Calibration mode dmfc6

58 Calibration mode dmfc7

58 Calibration mode dmfc8

58 Calibration mode customer zero9

1 2 ... 29 30 31 32 33 34 35 36 37 38 39 ... 42 43

Kommentare zu diesen Handbüchern

Keine Kommentare

Bronkhorst RS232 interface Bedienungsanleitung Seite 34

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Software Bronkhorst RS232 interface